Tag - Car Engine Cleaning

How to Clean the Car Engine

How to Clean the Car Engine in Eight Steps

The tips made by experts, who explains how we should perform the cleaning of our car’s engine, where to have more caution and the benefits of having every mechanical component clean.

The cleaning of the engine is divided into several steps. If you follow them with caution, you will get a propeller with a new appearance, thus avoiding corrosion or any other problem that may arise due to dirt. There is also a special emphasis on the type of car, differentiating between the types of engines since the coatings and the parts in the air vary from one to another. These tips are linked to those of cleaning the upholstery, and the keys to wash the car correctly, with which you will have the car as new.

Step 1: Do not scratch the car during cleaning

The first recommendation is to cover with a towel or rag the areas of the car that we will support during cleaning, to avoid scratching the car with the belt or anything else.

Step 2: Check the motor temperature

It must be checked if the engine is cold, warm or hot. In most cases the logical thing is to clean the engine at a temperature between cold and warm, but in others it is advisable to clean it with the hottest engine. This case would be if the engine takes a lot without cleaning or accumulates much dirt. The higher the temperature, the easier it will be for the dirt to dissipate.

Once the temperature has been checked, a pressurized air machine can be used to remove the dirt that remains in the body covered by the hood. Normally these areas fill with leaves of the trees and take a lot of dust, so that the pressure air in those nooks and crannies is the best solution.

Step 3: Waterproof the delicate areas of the engine

This step is one of the most important to avoid that a simple cleaning becomes a breakdown. We must cover with plastic and help us with insulating tape to waterproof well the areas of the engine that can be affected badly by water.

All electrical components, battery, distributor, carburetors, filters … must be covered with plastic so that the water never reaches them. If this happens it can lead to a fault for the motor. We must also take care to remove greases from the areas where they are needed.

Step 4: Wet the engine without water under pressure

In this step we must wet the engine in a smooth way and spread over all areas.

Step 5: Apply a multi-purpose cleaner

Once the entire engine is wet, we can apply a multi-purpose cleaner, and with the help of a brush start distributing and cleaning the entire engine. It is important to distribute the entire cleaner before it evaporates or dries on any part, working all the time with the wet motor. For less accessible areas it is recommended that we use smaller brushes and thus reach any side.

Once we have done everything, we will have to wet everything again to finish cleaning the engine.

Step 6: Drying the motor

Now it would be time to dry the engine, which can be done with air or with simple towels, making sure that everything is dry.

Step 7: Remove the plastics that we put

It is time to remove all the plastic with which we waterproof the areas critical to the water, taking special care to remove them in not spilling the water that remains on them. It would be a pity that after cleaning and good insulation of these areas, water was dropped on some unwanted part when removing them.

It would be convenient to pass a towel to make sure everything is dry, and so the water does not reach any of these areas once the plastics have been removed.

Step 8: Polish plastics and wait to start the engine

Once dry everything can be used to pass some polish to the areas with plastics, so that everything is shinier after cleaning.

In many cases it is advisable to wait a couple of hours after cleaning to restart the engine. After that time, it is advisable to start the car and leave it on for two or three minutes, watching and hearing the engine to know if there is any noise or something that is not correct after cleaning.

At this point you will have the engine shining as the first day, safe from corrosion, avoiding breakdowns, and therefore a safer and more reliable car.

We know that many of you are crazy about your cars and want to take care of them every day more, in order to have a nice car at the same time as the day in all aspects of mechanics and safety.

5 Tips To Drive Safe On Hot Days

These recommendations are ideal to handle when temperatures are too high.

With the arrival of summer, it is common that in many regions of the country the temperature rises considerably, which favours a warm climate. Obviously, this heat is not only felt outdoors but also felt in the car. It is proven that the interior of the vehicle can reach temperatures of more than 60 degrees Celsius; this excess heat causes the air actuated take more time to lower the temperature.

These high temperatures in the car’s interior not only make driving uncomfortable but also reduce the concentration and responsiveness of those behind the wheel. Therefore, the risk of suffering an accident increases considerably.

Car Detailing Services Christchurch

Faced with this situation, some measures must be taken in order to prevent the interior from getting too hot:

Hot Days Driving Tips

1.-Since the crystals in addition to letting the sun’s rays increase the temperature, it is best to ink the windows and/or place a sunscreen on the windshield. In any case, try to park the car in a shadow, or in the opposite direction to the sun’s rays.

2.-It is also advisable to leave the windows and the panoramic roof slightly down in case the vehicle has it. Once we start our tour you have to turn on the air conditioning and lower the windows completely for a few moments so that hot air accumulates.

3.- Another thing that is advised is to use a sleeve or apply sunscreen in case the sun’s rays are facing the left side, to protect the skin from UV rays.

4.-As much as there is too much heat outside, it is advisable that the temperature of the air conditioning is around 21 degrees Celsius. In addition, the interior of the vehicle should not be cooled too much so that there is no great difference when leaving the car, as it can cause respiratory problems. Also, it is best to direct the air upwards and not to the head or body.

5.-Regardless of the air conditioning, it is very important for hot trips the intake of liquids (water and tea) avoid dehydration.

Car Engine Cleaning Tips

How to Clean your Car | Car Cleaning Tips

Car Engine Cleaning tips onlineCar Engine Cleaning Tips

For many, everything that is not visible from the outside does not deserve to be cleaned. Beyond the concern for aesthetics, our car has many components sensitive to dirt that can deteriorate severely over time and when we talk specifically about the power plant, the problem takes important dimensions.

If the motor is covered with dust, in the short term it will not affect the operation at all; But over time a solid layer of earth can be deposited in the radiator and generate a loss of cooling, which causes an increase in the temperature of the engine, shortening its useful life and can generate various problems.

In addition, if dirt accumulates in the air conditioning condenser, it can cause the loss of cold air entering the passenger compartment, making this system less efficient and increasing fuel consumption to achieve the desired temperature, as we are forcing others to the team.

On the other hand, if the dirt is due to oil leaks, it can accumulate and mix with dust, mud or dirt, causing damage to the parts of the engine that are made of rubber, rubber, and plastics.

But as in Detail King, we do not like to give you problems, we are going to give you the solution so that you have your engine shining and working as it should:

Write down the ingredients, to clean the engine properly you will need:

  1. Detergent
  2. A plastic bag
  3. Water
  4. Thick aluminum foil
  5. Brush

Let’s go step by step:

1) Start the engine and allow it to warm up a little, but without letting it reach normal operating temperature. You can leave it on for a minute or a little longer if it is very dirty.

Car Cleaning Services Christchurch

2) Place the car in an area where the soap and the material you clean from the vehicle will not cause damage or stains.

3) Remove the cable from the negative terminal of the battery (usually black), then the positive (usually red) and cover the exposed electrical components with the bag or some plastic wrap. This will prevent the battery, fuses and other electrical components of the car from getting wet.

4) cover the air intake and the carburetor (on older engines) with thick aluminum foil or plastic. Water can cause serious problems if it is allowed to enter these areas.

5) To wash: Brush any dirt or debris on the surface of the motor, either using a brush to paint stiff bristles or a brush with plastic bristles for cleaning.

6) Mix 2 cups of anti-grease detergent in 4 liters of water and pass this solution in the dirtiest parts of the engine. Then, the fun part, rinse with a pressure hose without wasting water.

7) Remove the protectors that were used to cover the sensitive components.

8) Start the engine and let it idle so that the moisture evaporates and does not affect any element.

In order to keep the engine clean, a prevention mechanic is always advisable. It is not recommended to clean the motor too often because it has delicate components, which can be damaged if exposed to water. Therefore, the cleaning that is done will depend on the use of the car.