Monthly Archives - August 2018

How to Clean the Car Engine

How to Clean the Car Engine in Eight Steps

The tips made by experts, who explains how we should perform the cleaning of our car’s engine, where to have more caution and the benefits of having every mechanical component clean.

The cleaning of the engine is divided into several steps. If you follow them with caution, you will get a propeller with a new appearance, thus avoiding corrosion or any other problem that may arise due to dirt. There is also a special emphasis on the type of car, differentiating between the types of engines since the coatings and the parts in the air vary from one to another. These tips are linked to those of cleaning the upholstery, and the keys to wash the car correctly, with which you will have the car as new.

Step 1: Do not scratch the car during cleaning

The first recommendation is to cover with a towel or rag the areas of the car that we will support during cleaning, to avoid scratching the car with the belt or anything else.

Step 2: Check the motor temperature

It must be checked if the engine is cold, warm or hot. In most cases the logical thing is to clean the engine at a temperature between cold and warm, but in others it is advisable to clean it with the hottest engine. This case would be if the engine takes a lot without cleaning or accumulates much dirt. The higher the temperature, the easier it will be for the dirt to dissipate.

Once the temperature has been checked, a pressurized air machine can be used to remove the dirt that remains in the body covered by the hood. Normally these areas fill with leaves of the trees and take a lot of dust, so that the pressure air in those nooks and crannies is the best solution.

Step 3: Waterproof the delicate areas of the engine

This step is one of the most important to avoid that a simple cleaning becomes a breakdown. We must cover with plastic and help us with insulating tape to waterproof well the areas of the engine that can be affected badly by water.

All electrical components, battery, distributor, carburetors, filters … must be covered with plastic so that the water never reaches them. If this happens it can lead to a fault for the motor. We must also take care to remove greases from the areas where they are needed.

Step 4: Wet the engine without water under pressure

In this step we must wet the engine in a smooth way and spread over all areas.

Step 5: Apply a multi-purpose cleaner

Once the entire engine is wet, we can apply a multi-purpose cleaner, and with the help of a brush start distributing and cleaning the entire engine. It is important to distribute the entire cleaner before it evaporates or dries on any part, working all the time with the wet motor. For less accessible areas it is recommended that we use smaller brushes and thus reach any side.

Once we have done everything, we will have to wet everything again to finish cleaning the engine.

Step 6: Drying the motor

Now it would be time to dry the engine, which can be done with air or with simple towels, making sure that everything is dry.

Step 7: Remove the plastics that we put

It is time to remove all the plastic with which we waterproof the areas critical to the water, taking special care to remove them in not spilling the water that remains on them. It would be a pity that after cleaning and good insulation of these areas, water was dropped on some unwanted part when removing them.

It would be convenient to pass a towel to make sure everything is dry, and so the water does not reach any of these areas once the plastics have been removed.

Step 8: Polish plastics and wait to start the engine

Once dry everything can be used to pass some polish to the areas with plastics, so that everything is shinier after cleaning.

In many cases it is advisable to wait a couple of hours after cleaning to restart the engine. After that time, it is advisable to start the car and leave it on for two or three minutes, watching and hearing the engine to know if there is any noise or something that is not correct after cleaning.

At this point you will have the engine shining as the first day, safe from corrosion, avoiding breakdowns, and therefore a safer and more reliable car.

We know that many of you are crazy about your cars and want to take care of them every day more, in order to have a nice car at the same time as the day in all aspects of mechanics and safety.